DEFAULT        18 октября 2019        56         Комментарии к записи EJ6, D16Y7 — Civic DX, CX, LX, VP отключены

EJ6, D16Y7 — Civic DX, CX, LX, VP


Теперь для программирования микросхемы памяти, программатору нужно указать ваш тип микросхемы eeprom. Откроется новое диалоговое окно, с выбором микросхемы по марке и модели.

Диалоговое окно для выбора микросхемы памяти В открывшемся диалоге в первом столбце найдите компанию ST, для чипов AT Atmel. Во втором столбце найдите нужную модель M27CB, только в корпусе Dip После выбора чипа нажмите кнопку Select.

Установите необходимую микросхему в гнездо, ключ микросхемы, первая ножка, выемка на чипе по середине, должна быть направлена от светодиодов, ближе ключу тюнинг honda integra db6.

тюнинг honda integra db6

Далее из верхнего меню Device D выберите Programm P. Из открывшегося меню нажмите тюнинг honda integra db6 Program. Тюнинг honda integra db6 вынимайте микросхему из гнезда, пока не будет завершена запись программы на микросхему. Вынимать микросхему можно при работающей программе, и подключенном программаторе только тогда когда не происходит запись, чтение, стирание, или проверка. В открывшемся меню нажать Verify. Советую делать проверку после каждой записи прошивки на микросхему.

DIY termo gasket for intake manifold D16, Temperature In cold environment, the density of the substance increases. In a hot environment, increases the speed of the molecules. Air entering the intake manifold should not be heated, the denser the air will be the more powerful engine, which is why there is a turbo intercooler kits. Install the heat insulating gasket between the cylinder head and intake manifold D16Y7.

тюнинг honda integra db6

Hondata sells such, for D16 Civic. As a template, use the intake manifold gasket D16Y8. Gasket thickness mm. In home computer the hottest point is the CPU. For heat removal or use copper and aluminium radiator. Тюнинг honda integra db6 combustion temperature above degrees, exhaust manifold is heated to degrees.

Программатор MiniPro TL866, TL866A, TL866CS

All under hood area gets very silno. Chto bad, especially in the summer. A good тюнинг honda integra db6 is to install a thermal interface of copper to your EJ6 D16Y7. And of course winding exhaust manifold, heat tape. The first time she smells bad, but your exhaust manifold is hot.

Inlet must be cold and hot exhaust.

тюнинг honda integra db6

This gives better cross the air and the gas flow. Porting Typically, the compound of two parts, such as intake manifold and throttle or manifold and the cylinder head, not immeyut perfect pass.

тюнинг honda integra db6

At the junction there is тюнинг honda integra db6 a step. The tread is the resistance to air flow. With Dremel you need maximum cross-flow is achieved. And Intake and Exhaust. A little hardcore! Standard piston P2E, it is terrible. If you set PM3 in D16, your compression ratio will be It is very much, bad. Or if you are тюнинг honda integra db6 a piston factory D16Y7 P2E, just mill the cylinder head to 0. This reduces the combustion chamber, but will give a compression ratio CR of 9. Your engine bay space should look like this or better, this 1.

How much do I get horsepower?

EJ6, D16Y7 — Civic DX, CX, LX, VP

It all depends on whether you understand what the item as works if you do it right, you can increase тюнинг honda integra db6 percents. Do not try to install all the details without understanding the process.

Small injectors Problem injector D16Y7 only cubes. They were put on 1. If you just change the nozzle eg D16Z6, D16Y8 you will have a very rich mixture.

тюнинг honda integra db6

  Метки: ,